Krick Kits

Anna

Add to cart
Krick Modellbau
K20211

Part No.: K20211
Scale: 1:10
Length: 610mm
Beam: 260mm


Beginner/Intermediate
(click for details)

Anna - Open Launch

Anna is a small open launch, the ideal for introduction to steam sailing.
The hull is vacuum formed ABS, all timber work is CNC cut making this a very easy model to construct, the figure and fenders are additional accessories.
Optional steam plant.

Anna Steam Plant V2

Add to cart
Krick Modellbau
K20215
Anna Steam Plant V2 - Single Cylinder

This single-cylinder steam engine was developed mainly as a propulsion for the Krick Anna. Of course, the engine is also suitable as a drive for other model boats of about 50 cm in length or displacement of 1-2 kg.
With its compact design and vertical boiler, the steam engine is a real eye-catcher and a technical highlight for the small steamboat.
The steam engine is delivered completely pre-assembled. The boiler is ready soldered, pressure tested and painted. The steam line is already installed. The operation was deliberately kept very simple. Fill the boiler, heat up and start the engine on the flywheel. Use the small hand wheel to adjust the amount of steam and off you go.
Esbit tablets (not included) are used as fuel.

Alexandra

Add to cart
Krick Modellbau
K20281C

Part No.: K20281
Scale: n/a
Length: 940mm
Beam: 190mm


Beginner/Intermediate
(click for details)

Alexandra - Steam Launch
This kit is of outstanding quality. All plywood parts have been laser cut. Moulded from 1.5mm ABS, the hull is extremely strong. Propeller and shaft are also included.
Kit supplied complete with fittings kit including: 1 table lamp, 1 compass, 2 hand lamps, 1 boatswain, 6 side fenders and a bow fender.

Borkum

Add to cart
Krick Modellbau
K20291C

Part No.: K20291
Scale: 1:12
Length: 900mm
Beam: 330mm


Beginner/Intermediate
(click for details)

Borkum - Steam Island Provider
The Borkum kit is very easy to build. The hull is made from vacuum formed ABS and is fully CNC cut at the deck and all wooden parts are exactly cut out by laser. Screw shaft and pipe as well as brass prop and the complete rudder with linkage are included in the kit.Kit supplied complete with fittings kit including: side fenders, bow fender, twin bitts, lifebelts, flags with flagstaffs, lamp, bell, boatswain, fireman.

Felix

Add to cart
Krick Modellbau
K20300
4025792055140

Part No.: K20300
Scale: 1:25
Length: 634mm
Beam: 148mm
Height: 270mm


Beginner
(click for details)

Felix - Harbour Launch

The hull is deep-drawn from high-quality ABS plastic with integrally formed keel, so that the installation of prop shaft and rudder offers no difficulties. A bead for the bottom plate and the waterline is also marked on the hull, so that the beginner has no construction problems.
All deck and superstructure parts are carefully and accurately laser cut and the simple plug-in system makes the construction extremely simple. Furthermore, various motor bulkheads for different motor variants are included and the motor can be easily removed together with the mounting bracket at a later date.
An electric motor with articulated coupling is already included as standard, together with a prop shaft and steering gear.
All illustrated fitting parts are already prefabricated from wood or plastic included in the kit. The detailed building instructions and a building plan are specially designed for beginners.

Lisa M

Add to cart
Krick Modellbau
K20320
4025792099267

Part No.: K20320
Scale: 1:25
Length: 690mm
Beam: 205mm
Height: 310mm


Beginner/Intermediate
(click for details)

Lisa M - Motor Yacht

The hull is deep-drawn from ABS and thus ensures absolutely simple installation of the drive unit with the best possible water-tightness and safety while driving.All parts of the cabin are laser cut from plywood. This easy construction method is ideal for the beginner to learn basic knowledge and to guide you through to completion of a beautiful model.The deck is made of one piece of plywood and contains a large opening for easy access to the interior. The complete assembly can be removed in one piece.
All fitting parts, made of plastic or metal, are included in the kit.
A powerful 480 class motor with interference suppression capacitors, cables and flexible coupling is included as drive unit. Detailed instructions with many step-by-step illustrations and a 1:1 construction plan are also included.
 
The dinghy is available as an additional kit. But even without a dinghy at the stern, this model looks great.

Dinghy

Add to cart
ROMarin by Krick
R1577
Dinghy - With Outboard & Steering Wheel
Blown from ABS, floatable, with outboard motor and steering wheel
Length 140mm.

HE 4 Police Boat

Add to cart
Krick Modellbau
K20330
4025792106552

Part No.: K20330
Scale: 1:20
Length: 760mm
Beam: 195mm
Displacement: 1700g


Intermediate/Advanced
(click for details)

HE 4 Police Boat - Patrol Launch

One-piece GRP hull with structured deck, GRP wind hood, shaft systems, rudders, couplings, plastic profiles, brass wires, approx. 300 laser-cut individual parts, fittings, decal sheet and detailed building instructions with construction plan.

HE 4 Internal Detail Set

Add to cart
Krick Modellbau
K20331
HE 4 Internal Detail Set
Add more to the scale appearance of your HE 4 Police Boat with this custom Internal Detail Set.

HE 4 Lamp Set

Add to cart
Krick Modellbau
K20332
HE 4 Lamp Set - Lamp Housings
This lamp set for the police boat HE4 contains:2 Blue housings for flashing lights, with aluminium base1 Pair of position lights red/green lense2 Clear flashing alarm lamps2 Section lights (front/rear)
 
Please note, this is a lamp set only (no bulbs).

Police Boat WSP47

Add to cart
Krick Modellbau
K20360
4025792132681

Part No.: K20360
Scale: 1:20
Length: 600mm
Beam: 205mm
Height: 335mm


Beginner/Intermediate
(click for details)

WSP47 - Police Launch

The kit contains the finished deep-drawn ABS plastic hull, shaft with stern tube, coupling and drive motor with cables.
For deck and superstructure, all plywood parts are precisely cut out with a laser. All parts for the many fittings are also included in the kit, including the fire monitor and the rotating radar.
A detailed building instruction and building plan drawings make it possible even for the beginner with some skill to build this versatile model.

Antares

Add to cart
Krick Modellbau
K20370

Part No.: K20370
Scale: 1:20
Length: 1260mm
Beam: 220mm
Height: 1530mm
Displacement: 6500g


Intermediate/Advanced
(click for details)

Antares - Cutter Yacht

Antares kit with GRP fuselage and laser-cut wooden parts as well as fittings. Further accessories, such as the rigging set and sails, are needed to complete the boat.
The model is certainly not a mass-produced model; although a finished epoxy hull is included in the kit and all wooden parts for the deck and superstructure are also available as laser parts, making construction quick and uncomplicated. The deck is completed completely outside the hull as a separate supporting assembly and only then glued into the hull as a whole. All materials required for construction are included. Only the fittings for rigging the mast, such as brass blocks, shroud tensioners, stainless steel cable, lines are included in the specially supplied rigging set, which is only needed later. For calm, an auxiliary drive has been installed in the model, which is available as an additional accessory set.
Drawings for the sails are included in 1:1. You can either purchase fabric to sew yourself or a finished set of sails. The detailed building instructions, in which each stage of construction is shown in pictures, and also describes the detailed control of the two headsails true to the original, and a detailed building plan make the construction of the model also possible for the non-expert without any problems. The equipment can be equipped with 2 or 3 sailing winches. The winches can also only be installed after the model has been completed.

Nordstrand

Add to cart
Krick Modellbau
K21430

Part No.: K21430
Scale: 1:16
Length: 850mm
Beam: 315mm


Beginner/Intermediate
(click for details)

Nordstrand - Trawler Yacht

Nordstrand is a freelance model of a fishing yacht.
With a vacuum formed ABS hull and superstructure, die-cut timber and plastic parts and fittings as shown in the photograph. Two full size plan sheets and a detailed instruction manual. This model is an excellent on the water performer and ideal as a regatta model.

Grimmershorn

Add to cart
Krick Modellbau
K21440

Part No.: K21440
Scale: 1:16
length: 1038mm
Beam: 305mm


Intermediate
(click for details)

Grimmershorn - Pilot Boat
The model hull and deck are vacuum formed ABS, timber work of precision cut ply, 2 full size plan sheets and a construction manual along with a fittings pack complete this kit.

Sirius

Add to cart
Krick Modellbau
K21460

Part No.: K21460
Scale: 1:16
Length: 900mm
Beam: 330mm


Intermediate/Advanced
(click for details)

Sirius - Crab Cutter
The kit comprises of a one piece vacuum formed ABS hull, a fittings set including the winch which is manufactured in brass as is the majority of fittings. Precision cut ply parts, net material, wood, dowel, brass tube and wire help make this a superb kit. Very detailed full size plans and a comprehensive instruction manual make this kit a pleasure to build and sail.

U-Boat Type VIIb

Add to cart
Krick Modellbau
K20310C

Part No.: K20310C
Scale: 1:60
Length: 1120mm
Beam: 127mm


Intermediate
(click for details)

U-Boat Type VIIb

Includes running gear!

This is a highly detailed kit complete with:
Twin screw drive, including motors and props; two cast white metal gun kits; ABS manufactured hull; fully detailed deck; all necessary rigging; step by step instruction manual with full detailed plan sheets.
Ideal as an introduction to the world of submarine building.

!